This revision permits the publication of BS EN to be adopted as a Harmonised Standard under the Constuction Products Directive. BS EN. Hot finished structural hollow sections of non-alloy and fine grain steels -. Part 1: Technical delivery conditions d Copy. Find the most up-to-date version of BS EN at Engineering
|Published (Last):||1 August 2014|
|PDF File Size:||17.12 Mb|
|ePub File Size:||2.95 Mb|
|Price:||Free* [*Free Regsitration Required]|
Hs A range of material grades is specified in this standard and the user should select the grade appropriate to the intended use and service conditions. The inspection certificate shall contain the following codes and related information in accordance with EN The test report shall contain the following codes and relevant information in accordance with EN Click to learn more.
Method of test at ambient temperature EN Technical delivery requirements Status: General requirements for welding of the products in accordance with this European Standard are given in EN and EN For undated references, the latest edition of the referenced document including any amendments applies. Document Status Indicators The Green document status indicator indicates that the document is: B — Description of products to which the inspection certificate applies.
This declaration shall include: Technical delivery conditions for non-alloy structural steels ENHot rolled products of structural steels — Part 3: To consider the test unit as conforming after testing the second set, the following conditions shall all be satisfied simultaneously: Impact tests eb be carried out at the temperatures specified in Table A.
Test method EN This does not preclude 102210-1 free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. BS EN In addition, initial type testing shall be performed: The BSI copyright notice displayed in this document indicates when the document was last issued. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 38, an inside back cover and a back cover.
Various BSI electronic information services are also available which give details on all its products and services. The following samples shall be taken from one sample product of each test unit: Otherwise, the NPD option may be used when and where the characteristic, for a given intended use, is not subject to regulatory requirements in the Member State of destination.
If the nominal product thickness is not sufficient for the preparation of standard test pieces, the test shall be carried out using test pieces of width less than 10 mm, but not less than 5 mm. Steel hollow sections To be used in metal structures or in composite metal and concrete structures Requirement clauses in this European Standard EN Design of steel structures – Part BS EN specifies the wn delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed product.
BS EN for Hot Finished Structural Hollow Sections
In order to meet the provisions of the EU Construction Products Directive, these requirements need also to be complied with, when and where they apply. Those relevant to this part are listed below with appropriate clause references. Worldwide Standards We can source any standard from anywhere in the world. Search all products by. This declaration and certificate shall be presented in the official language or language s acceptable to the Member State in which the product is to be used.
The bz should preferably select hollow section dimensions from this limited range of sizes.
BS EN 10210 for Hot Finished Structural Hollow Sections
B — Description of products to which the test report applies. Take the smart route to manage medical device compliance. In case of dispute, the method used shall be agreed taking into account CR NOTE European legislation without national derogations need not be mentioned.
The standard to be applied is at the discretion of the manufacturer. NOTE 1 In addition to any specific clauses relating to dangerous substances contained in this standard, there may be other requirements applicable to the products falling 102100-1 its scope e.
Overview Product Details BS EN specifies the technical delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, 10210-11 or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed product.
SJ2H structural hollow section according to EN – SSAB
All equipment used in the manufacturing process shall be regularly inspected and maintained to ensure use, wear or failure does not cause inconsistency in the manufacturing process.
By option to specify that the product is suitable for galvanizing. Revisions British Standards are updated by amendment or revision.
EN and EN 6.
In cases where this would mean assessment of steel hollow sections for ej type testing in accordance with this standard had already been performed, the testing frequency may be reduced: CC03 —Direction of test pieces and test temperature; CC13 — Tensile test — Test piece shape and test results; CC43 — Impact test — Test piece type and test results, if applicable; CC92 —Cast analysis and, if applicable, product analysis.
This gs in particular to personnel that needs to initiate actions preventing product non-conformities from occurring, actions in case of non-conformities and to identify and register product conformity problems.
Hollow section for general applications
The minimum frequency of testing shall be in accordance with Table D. Structural hollow sections of fine grain steels shall conform to the requirements of Annex B.
The grades and mechanical properties of the finished hollow sections are compatible with those in EN and EN Copyright Copyright subsists in all BSI publications.
Tolerances, dimensions and sectional properties It forms part of a series of standards on hollow sections together with EN and 2, ne are also under revision.