Buy the Faac Backup battery for EO24S from Linkcare Gate Automation – Description. Power supply voltage Vac; 24V panel; Absorbed power 4 W; Motor max load W x 2; Accessories t mA; BUS accessories. FAAC-ES-manual. ES INDEX 0 BOX LAYOUT. .. B CONTROL UNIT ES 1 WARNINGS Before attempting any work on the control unit (connections .

Author: Takazahn Mokinos
Country: Samoa
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 16 June 2007
Pages: 170
PDF File Size: 17.26 Mb
ePub File Size: 3.25 Mb
ISBN: 931-5-88436-558-2
Downloads: 51641
Price: Free* [*Free Regsitration Required]
Uploader: Arashirr

Install and program the accessories using the required address see paragraph 7.

This includes neutral feedback. Please don’t purchase if you don’t intend on paying, non payers will be reported to ebay.


Report item – opens in a new window or tab. Check the status of the signalling LEDs as per table below: Seller assumes all responsibility for this listing. To add other radio controls, repeat the operation at point 1. Make sure that there are no two or more photocells pairs with the same address. The relevant LED starts to flash slowly for 5 sec.

Doesn’t post to United States See details. Watch list is full. The LED on the board relating to the channel being learned flashes for 5 sec.

From now until the next Open impulse, the pause time is counted.

Visit my eBay store. NO – Reverse Stroke: Packaging should be the same faaac what is available in a retail store, unless the item was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. Only one radio code can be used at a time.


The default configuration is reset and the new Setup can be started. The menu is scrolled sequentially. No additional import charges at delivery! The LED relating to the pressed push-button flashes for the first 5 sec, and then flashes more quickly for the next 5 sec.

If Open is detected, a stop in closed position is set only with absolute encoder Enc For the safety of people, it is ep24s that all the instructions be carefully observed. The item you’ve selected wasn’t added to your cart. Then the leaves start moving, one at a time, from the closed position with an do24s command or automatically.

Faac Backup battery for EO24S

DL 2 determines the leaf on which the encoder is installed. Starting from leaf opening 2. Once an opening stop or an “open” impulse is detected, they reach the open position and the setup is ended.

More information at returns. The time can be set between 0 and 4. It’s a community-based project which helps to repair anything. Connect the two accessories cables to the red terminalboard Faaf any polarity will do. A maximum of 16 BUS photocell pairs can be connected to the board.


FAAC-ES-manual |

The LED lights up on steady beam for 2 seconds, indicating memory storage executed, and then resumes flashing for 5 sec. B shows the four 5 mm diam. Image not available Photos not available for this variation. Back to home page.

If a stop is detected, an closing stop search is set. Learn more – opens in a new window or tab International postage paid to Pitney Bowes Inc. If you have any problems, issues or concerns contact me first and I will do my best to solve them.

De beschrijvingen in deze handleiding zijn niet bindend. DL 3 indicates, on a steady flashing beam, the reading of the pulses while the leaf is moving. Power up the board, taking care to first connect the main power supply transformer output and then any batteries.

YES – Leaf closing delay: Then the procedure described in paragraph 6. In this situation, refer to the configuration in TAB. A brand-new, unused, unopened, undamaged item in its original packaging where packaging is applicable. E Next, tighten the four supplied screws to guarantee the degree of protection against external agents Fig.

When the 5 sec.

If there is an incorrect connection, i.