IC CD4011 PDF

Sep 21, #Working and pin configuration of the #NAND #IC CD A door opening indicator circuit using IC gate IC and working of NAND gates. CD TRUTH TABLE. The CD is the most used CMOS chip. The CD IC has 4 gates and these can be wired to create a BUFFER, Inverter (NOT) . ooÕoo This article starts with a detailed look at the operation of the Cmos It then considers the practical use of the IC in the small alarm circuit on the .

Author: Tygojora Maukasa
Country: Djibouti
Language: English (Spanish)
Genre: Music
Published (Last): 9 May 2011
Pages: 244
PDF File Size: 15.41 Mb
ePub File Size: 11.79 Mb
ISBN: 120-9-40066-781-1
Downloads: 87287
Price: Free* [*Free Regsitration Required]
Uploader: Visar

The resistors also keep Vcc from directly shorting to ground when the pushbutton is pushed down. This circuit was wired as a door open indicator which indicates the opening of door using the bulb which was connected to the output pins of the gates. This way, we can see what combinations of inputs will make the NAND gate be off and what inputs make it turn on. Frank Donald June 14, 1 Comment. Now let us see how this Integrated circuit works and how can we use it for our operations.

Let me tell you why, usage of large range of the NAND gates occupies more space and also it withdraws more power arising problems in power management to a circuit. Latest posts by Frank Donald see all.

How to Build a NAND Gate Logic Circuit Using a 4011 Chip

And these situations comprise all the situations that can arise for a 2-input NAND gate. For this circuit, we will connect pushbuttons to the 2 inputs of the NAND gate. When either one or both of the pushbuttons are pressed, the NAND gate will output a logic HIGH or 1and the load connected to output will be c4d011 on. This makes the bulb to glow fd4011 that the door is not properly shut. Each NAND gate has input pins and 1 output pin. In our circuit, we will use both of these cases.

  DHATU MANJARI PDF

However, it is a very popular chip and many electronics parts suppliers have them. These resistors function as pull-up resistors. Here in this circuit the input pins of the are connected to the supply voltage directly as shown in the diagram.

When we press down on a pushbutton, it changes to a logic level of LOW. Quote and Order boards in minutes on: However, in this circuit, we will just use one NAND gate, to make the circuit as simple c4d011 possible.

This establishes power to the chip. This circuit is as basic as it gets for a NAND gate circuit and it demonstrates all the possible input values that a NAND gate chip can receive and output.

As a result the the bulb will not glow due to low output obtained from the output pins of the gates. Frank Donald is an Electronics and Communication Engineer who loves building stuff in his free time.

Practical Electronics/IC/4011

Notify of all new follow-up comments Notify of new replies to all my comments. The quad NAND gate chip can be obtained very cheaply from a number of online retailers for just fd4011 few cents.

The output pins of the IC are 3,4,10,11 and input pins are 1,2,5,6,9,8,12, Each output can deliver output current of about 10mA at 12V but this range can reduce as the power supply voltage reduces. Thus, we can test out all logic levels. We can see the state of the output pins with the assigned inputs in the truth table given above. This IC was used since it withdraws only small power and also reduces the complexity of the circuit.

How to Build a NAND Gate Logic Circuit Using a Chip

Thus, the pushbuttons, when left alone, unpressed, will normally have a logic value of 1. This makes the gate to change its output state from low to high. First and foremost, we must give power to the NAND gate chip. There we can see that the NAND gate gives a high cc4011 to all the input states except the input states 1,1.

  LES MISERABLES THE CONFRONTATION SHEET MUSIC PDF

Working of CD IC – Gadgetronicx

When a pushbutton is pressed down, the pushbutton now makes contact across to ground. Below is the breadboard schematic version of the above circuit so that you can see the exact wiring of the circuit to the chip. Video games, blogging and programming are the things he loves most. Each NAND gate has two inputs and one output. When the doors are open the gate inputs will be 1 and the output of the ic 0 which will turn the bulb off. The positive terminal of the battery was connected to the pin 14 and negative terminal of the battery was connected to the pin7.

Closing a door will input level 0 and output level 1 causing bulb to light. So the LED will turn on in this case. One place ce4011 can be obtained from is Tayda Electronics at the following link: If the door was open or it is not properly shut, logic 0 is applied to the gate input.

N4 was wired independently and there is no dependency on other gates. The pinout of the is shown below, so that you can see how to connect it in the circuit.

The following two tabs change content below. When the door was closed push button switch, it apply logic 1 to the gate input. The corresponding input pin will now be grounded and its logic level will change to a logic LOW now that it makes contact down to ground. The combined action of the these four gates form the working of this IC CD