JTAG PANTEC PDF

Pantech Solutions. Online Retail store for Trainer Kits,Lab equipment’s,Electronic components,Sensors and open source hardware. This process is to assist in the repair of your Pantec receiver. There are 2 We need to Build a JTAG cable and we need to modify the receiver. To modify the. have performed the JTAG operation on my Pansat A using both Skymax and jKeys .. The first thing to do here is figure out if you have a PanTec MX or MS.

Author: Kazisho Kijora
Country: Thailand
Language: English (Spanish)
Genre: Health and Food
Published (Last): 28 April 2012
Pages: 372
PDF File Size: 16.6 Mb
ePub File Size: 9.2 Mb
ISBN: 786-3-16936-507-4
Downloads: 97648
Price: Free* [*Free Regsitration Required]
Uploader: Yokazahn

This is repeated for DB25 Pin 3,4,5. Now confirm all connections and make sure you haven’t left anything inside the unit that could short. Make sure you get a similar screen.

Once your comfortable with which pins, take a pen knife with panyec thin blade or a razor knife and gently bend the pins closer together from half way between the chip and the board. Simply click open once you.

Gently remove the receiver board from the case. I would mount the board here as shown above. Now attach the DB25 wires to the appropriate spot as well as the flat ribbon 10 pin connector.

Introduction to JTAG – Developer Help

For this step of the procedure, you will need some software. The board should now be in a position to solder the parts into their final position. Remember to ground yourself before touching the board. Take a heat sink and fan.

Pantech | RIFF Box – Best JTAG Box in this Galaxy 🙂 Easy to operate !

The solder tabs on the board are already tinned and ready for the mod. Follow these steps and you can use it again. Just a sec or 2 will be enough to meld the tinned end to the already solder prepared tab. I think cheaper is always better.

  ADA COLAU VIDAS HIPOTECADAS PDF

Click the pull down tab panrec select it. Don’t touch anything until the completed box appears. The 5 resister bank shown below will be missing the 4th resister. Power up the unit and confirm that it still turns on and goes beyond the night rider stage. Examine the photo below and make sure your looking at pin and On the MS this is the orange wire closest to the rear ktag the machine on the connector.

For this step of the procedure, you will need the following parts. Add Existing Items From Folders Once accomplished, after tinning the iron and cleaning off the residue, touch the iron at the point the pins touch.

If the receiver lights up then all is well.

The new MX has the modifications necessary to prevent the problem. When you click the Program button you will get a.

Watch headings for an “edit” link when available. There are holes under these tabs filled with solder and this must be removed.

Download the file to the receiver and wait until complete. No big balls of solder are allowed. Then we apply the auto roll flash by serial interface. Also make sure that you can place the board inside the box and put the lid on. Configure drivers for the application Step 3: Remove the case screws and remove the top panel of the case.

Make sure the points underneath the header don’t touch the case bottom. You can call it anything and put it anywhere you will remember. You jtah have to off set the fan to clear the caps. Generate Harmony code Step 7: I have read about the buffered JTAG cable and I built one and found no difference in process or effectiveness.

  LIBRO EL ENCHIRIDION LEONIS PAPAE PDF

Many of these units are somewhat quirky in the sense that they may not react well ktag certain programs. Re-assemble the board into the case. We then have to clear the original flash on the receiver.

Which jtag is best for pantec mx

Its easy to make them touch. Next you want to add the fan. Generate Harmony code Step 8: Append content without editing the whole page source.

You will be able to solder from the points indicated in the board and run the wires to the header. Make a test with your meter and confirm continuity with no shorts.

Once completed the receiver jhag reboot and you will have only night rider lights. Allow the process to complete. If you experience problems with DCU errors in Jkeys, this will probably solve it. You can figure out with your iron exactly how long it takes to melt the solder but try and not take too pante. The rest of the wires are your data lines. Configure Evaluation Board Step 4: Then solder the wires as shown below.